- #THERMAL BUBBLE WRAP NEAR ME INSTALL#
- #THERMAL BUBBLE WRAP NEAR ME PLUS#
- #THERMAL BUBBLE WRAP NEAR ME FREE#
If the clamps are installed around the duct (such as plumbers tape), make sure that the seam is taped to prevent air movement.
#THERMAL BUBBLE WRAP NEAR ME INSTALL#
If the duct is supported with saddle clamps, make sure to install a spacer on the two bottom edges of the duct directly between the clamp and the duct.
Fasten the Reflectix® by either taping the seam with a UL 181 approved tape, or plier stapling the two edges together (goal is an air-tight, snug seam seal). #THERMAL BUBBLE WRAP NEAR ME PLUS#
Cut the Reflectix® product to this length plus 1”. 
Verify the circumference of the duct over the top of the spacers.
Install the HV Spacers to all 4 corners of the duct. #THERMAL BUBBLE WRAP NEAR ME FREE#
Make sure the duct is free from dust and dirt by wiping it down with a shop rag. Make sure all sheet metal joints, seams and penetrations are sealed. Refer to the lower two diagrams above. HV Spacers Affixed to Corners Method (Rectangular Ducts Only) Spacer: HVSpacer – Reflectix® HARD PLASTIC CORNER SPACER Cut the Reflectix® product to this length plus 1”.ģ. Verify the circumference of the duct with the spacer strips in place. Use a UL 181 approved tape to fasten the spacer in place. First, proceed down the duct in one direction then reverse direction and crisscross (overlap) the spacer in the other direction. Double wrap and secure spacer material to the duct in a candy cane fashion. Refer to the third and fourth (from the top) diagrams above. Spacer Wrapped in Candy Cane Fashion Method Spacer: HVSPW02025 – Reflectix® Spiral Pipe Wrap 2”x 25’ Do not leave any exposed duct or space where air can enter between the duct and the Reflectix®.Ģ. Wrap the product around the duct and securely tape the linear and circumference seams (overlapping 1”- 2”) with a UL 181 approved tape (goal is an air-tight, snug seam seal). Cut the Reflectix® product to this length plus 1”. Verify the circumference of the duct at the mid-point of a spacer strip. Double wrap and secure spacer material to the duct at 24” to 36” intervals. Spacer Perpendicular to Duct Direction Method Spacer: HVSPW02025 – Reflectix® Spiral Pipe Wrap 2”x 25’ R&D Services: Water Vapor Transmission Test ASTM-E96 (Dessicant Method)ġ. R&D Services: Physical Properties Sheet Width, Length, Pliability, Water Vapor Permanence and Aged Water Vapor Permanence. State of Minnesota: Filed with Minnesota Insulation Standards Program. State of California Licensed Insulation Manufacturer. R&D Services: Resistance to the Growth of Fungi ASTM C1338-00 Test Report # RD10510. Intertek: Test for Surface Burning Characteristics of Building Materials ASTM E84-10 (Unslit) Test Report # 100054110SAT-007G Rev 1. Intertek: Test for Surface Burning Characteristics of Building Materials ASTM E84-10b (Taped Joint Detail) Test Report # 100402776SAT- 001D Rev 1. Sound Transmission Loss ASTM E90 and ASTM E413. Sound Absorption Test ASTM C423 and ASTM E795. Fungus Resistance Mil-Std 810B Method 508. Flame Spread and Smoke Density ASTM E84. 
Thermal Conductivity and Thermal Resistance of Blanket ASTM C518.If you're concerned about condensation forming on either side of your metal building or pole barn, Double Bubble insulation is the product for you. Double Bubble foil insulation redirects 96% of radiant heat, and features an extra layer of bubbles to provide maximum protection against condensation build-up in colder temperatures.
0 kommentar(er)
